PRODUCTS

Designed to obtain fuel with similar indicators of diesel fuel standards, from kerosene of any brands. Namely, the indicators for lubricating (antiwear) and cetane properties correspond to diesel fuel. The additive tests were carried out on jet kerosene. 1. The wear scar diameter of jet kerosene is 670 µm (very poor lubricating properties). After adding the additive in a volume of 0.1% (1 liter per 1000 liters of kerosene), the WSD decreased to the level of 410 microns (high lubricating properties). According to the standard, the wear scar diameter of ​​diesel fuel should not exceed 460 µm . 2. The cetane number of jet kerosene is 44 (very low). After adding the additive in a volume of 0.1% (1 liter per 1000 liters of kerosene), the cetane number increased by 50 (almost the same as summer diesel fuel with a cetane number of 51 and surpasses everything in winter diesel fuel with a cetane number of 47). The additive allows the use of any brands of kerosene, as a substitute for diesel fuel in winter, but also in summer conditions, as a separate fuel and is used in mixtures in any proportions with diesel fuel in an internal combustion engine of commercial vehicles, diesel generators, any heating systems, and so on.

The recommended usage: 0.01%

We provide shipments to Belarus, Kazakhstan and the countries of the FSU and beyond

Designed for introduction into spent engine oil, pyrolysis fuel from rubber and plastic waste (with high density) before distillation. Helps to block the formation of carbon particles and ash in the gas phase, reduce sulfur content in the distillate and protect equipment from carbon deposits. As well as receiving light yellow oil at the outlet of the condenser. As a result, the oil distillate is not subjected to an additional bleaching process using sulfuric acid and bleaching additives, which allows to optimize the time and economic component of the regeneration process.

The recommended usage: 0.3% to 0.5%

We provide shipments to Belarus, Kazakhstan and the countries of the FSU and beyond

Used for bleaching, antioxidation and deodorization of oil, fuel, using sulfuric acid. Such types as oxidized diesel fuel, pyrolysis fuel from rubber or plastic, distillates of used motor oil, dark base oil. It is an analogue of the BleachingX additive, but it has a number of indisputable advantages. Namely:
1. Very high reactivity, due to which the reaction of clarification of fuel or oil occurs instantly.
2. Reducing the dosage of the additive due to the low density and viscosity.
3. The maximum reduction of polymerization in fuel or oil, bleaching products do not have turbidity after the use of additives.
4. The cleaned oil or fuel does not precipitate in the form of colloidal masses, which prevents the cleaning of the capacitive park.

The recommended usage: 0.1% to 0.2%

We provide shipments to Belarus, Kazakhstan and the countries of the FSU and beyond

Used for bleaching, antioxidation and deodorizing oil or fuel using sulfuric acid. Such types as, black diesel fuel, pyrolysis oil from waste rubber and plastic, vacuum distillates used engine oil, dark base oil.

The recommended usage: 0.2% - 0.4%

We provide shipments to Belarus, Kazakhstan and the countries of the FSU and beyond

Used for bleaching, regeneration of used industrial oils without the use of SULFURIC ACID. Such as the type, hydraulic, turbine, machine tool, etc.

The recommended usage: 0.2% - 1%

We provide shipments to Belarus, Kazakhstan and the countries of the FSU and beyond

Antioxidant additive is used in the production of all types of diesel fuel, vacuum gas oil, as well as in the production of base oil. Prevents the darkening of the resulting fuel in a mini refinery. It is used on oil depots for long-term storage of fuel by stabilizing it by inhibiting the process of oxidation and highlight resin.

The recommended usage: from 0.025% to 0.05%

Used to remove bad odor from all types of pyrolysis oils and fuels. Also for any oil dark and light medium distillate fractions, gas condensate and so on. After applying the additive oil, the fuel has a neutral smell. The additive does not contain flavors. It is applied by mixing in the storage tank or by dosing in the stream.

The recommended usage: 0.025% - 0.1%

We provide shipments to Belarus, Kazakhstan and the countries of the FSU and beyond

Designed to remove bad smell, such as hydrogen sulfide, mercaptans, the smell of burning in diesel fuel, gasoline, gas condensate, heating oil and pyrolysis oil. Excellent dissolution and quick reaction when mixed with fuel, oil.

Dosage range from 0.01% to 0.05%.

Used for bleaching the paint of diesel fuel or gasoline.(Heating oil)

The recommended usage: 0.025% - 0.03%

We provide shipments to Belarus, Kazakhstan and the countries of the FSU and beyond

The additive is designed to remove heavy metals and aging products (soot). Purification of the oil can be used as furnace fuel, including for the production of low-viscous bunker fuel.

The technology of additive production for sale.

Dosages range from 3% to 5%

It is used to lower the temperature of fluidity of oil with a high content of paraffin wax fractions, fuel oil, bunker oil of any brand, heavy vacuum gas oil, as well as VAT residue in the production of pyrolysis oil. It is applied by mixing in the storage tank or by dosing in the stream.

The recommended consumption is 0.1% -0.15%

Designed to obtain a stable water-diesel or water-oil emulsions with a water content of up to 50%. This water-emulsion fuel is well suited for burning on any diesel and oil burners. Also applicable for use on diesel internal combustion engines (diesel generators and so on). As a result of burning water-fuel emulsion, the boiler equipment is cleaned from soot, the emission of harmful substances into the atmosphere is reduced from 40% to 60%, and most importantly, money is saved for the purchase of diesel fuel. An important aspect, water-fuel emulsion can be made at home without using cavitation or ultrasonic technology, which greatly simplifies its production and use. Emulsifier dosages will be only 0.5% with respect to water (For 1000 liters of water, only 5 liters of emulsifier). The resulting water is successfully mixed in the right proportions with diesel fuel or oil. The stability of such an emulsion can be up to 1 week. In case of longer storage of the emulsion, mix again and use as intended.

Recommended dosages of water in diesel or oil. Internal combustion engine (Diesel generators and so on) - 10% -15% (without loss of power) Boiler equipment - 20% -35% (without loss of power)

Recommendation. Prepare a specific volume of the emulsion and use within 24 hours.

Designed to obtain a stable water-oil emulsion in the conditions of an oil base or boiler house without the use of expensive cavitation equipment and the use of electricity for water heating. As a result of receiving the emulsion, fuel oil has higher environmental performance, preventing pollution of the boilers, higher calorific value with full combustion of fuel. And most importantly, cash savings of up to 15% per 1 ton of fuel oil. The process of preparation of the emulsion is performed in a tank for storing fuel oil by mixing emulsion water and fuel oil through a gear pump. It is also possible to stabilize the fuel oil already watered earlier and to obtain a stable homogeneous structure.

The recommended emulsifier consumption is 0.5% by volume of water. The recommended water consumption for fuel oil is 15% (without loss of power).

Additive for increasing the flash point in base oils, commercial oils, as well as in secondary vacuum distillates of any used oils. The additive allows you to raise the flash point in oils that do not reach established standards for further use in the necessary conditions in accordance with operating standards. Does not change the technical properties of oils.

Additive properties: Raise the flash point in an open crucible from 20 to 30 degrees Celsius.

The recommended usage: 0.01% (100 ml per 1000 liters of oil).

Flavoring agent for mineral base oil
Designed to remove (block) unpleasant odors in base oil, diesel and pyrolysis fuel. The additive effectively removes the unpleasant burnt odor obtained as a result of secondary vacuum or atmospheric distillation of waste oils.

Recommended consumption: 0.03%-0.1% (300 ml-1 l per 1000 liters of processed product).